Ultrasonic Flow Meters

20+ Years Manufacturing Experience

Support

  • Why does the electromagnetic flow meter show fluctuating readings?

    Fluctuating flow values are the most common issue reported by users. Normally, this problem is not caused by product failure but by field working conditions. First, if the liquid contains air bubbles, suspended solids or unstable water pressure, the flow signal will keep jumping. Second, poor gro...
    Read more

  • Detailed Introduction of V / Z / W / N Installation Modes for Clamp-on Ultrasonic Flow Sensors

    1. V Mode (V Installation) V installation is the most widely used standard installation method. The two sensors are mounted on the same side of the pipeline. The ultrasonic signal is transmitted from one sensor, reflected once on the opposite pipe inner wall, and then received by the other sensor...
    Read more

  • Detailed Introduction: Clamp-on Ultrasonic Flow Meter for Seawater Application

    1. Application Scenarios Widely used in seawater desalination projects, coastal seawater intake & drainage engineering, marine aquaculture, seawater cooling circulation system for power plants and chemical plants, offshore platform fluid monitoring, port water pipeline management, seawater fl...
    Read more

  • Detailed Introduction of Clamp-on Ultrasonic Flow Meter for Pharmaceutical Industry

    1. Applicable Application Scenarios It is widely applied in pharmaceutical factories, biopharmaceutical workshops, medical reagent production lines, pharmaceutical purification workshops, pharmaceutical water treatment systems and pharmaceutical sewage discharge projects. It fully complies with G...
    Read more

  • Detailed Introduction to Ultrasonic Flow Meters in Food Industry

    1. Applicable Scenarios Widely used in food processing factories, beverage production lines, dairy plants, wine brewing factories, snack food workshops, condiment production workshops and food processing water supply and drainage systems. It is an ideal flow measuring device for food-grade produc...
    Read more

  • Detailed Introduction to Application of Ultrasonic Flow Meters in Water Treatment Industry

    1. Applicable Industry Scenarios Widely used in municipal water supply, secondary water supply, sewage treatment plants, reclaimed water reuse, water purification plants, industrial park water treatment, swimming pool water circulation, landscape water management, wastewater discharge control and...
    Read more

  • Electromagnetic Flow Meter: Horizontal vs Vertical Installation

    Which is better & Installation Rules 1. Conclusion Vertical installation is preferred; horizontal installation is acceptable but must follow strict installation rules. 2. Vertical Installation (Recommended) Advantages Avoid air bubble accumulation, sediment deposition and sludge settling. Al...
    Read more

  • Electromagnetic Flow Meter Electrode Material Selection

    Difference & Application: 316L / Hastelloy / Titanium / Tantalum 1. 316L Stainless Steel FeaturesGeneral-purpose & cost-effective; moderate corrosion resistance; poor resistance to high chloride, strong acid and oxidizing media; ordinary wear resistance. Suitable MediaClean water, tap wat...
    Read more

  • Electromagnetic Flow Meter: Maximum Temperature & Pressure Ratings

    The maximum temperature and pressure of an electromagnetic flow meter (EMF) are primarily limited by the liner material, electrode seals, coil insulation class, and flange rating. Below is a structured breakdown of standard and extreme limits. 1. Maximum Temperature Ratings (by Liner Material) Ru...
    Read more

  • For electromagnetic flow meters, what working conditions are respectively suitable for rubber lin...

    1. Rubber (Natural/Neoprene/CR) Best for: General‑purpose, low‑to‑moderate corrosion, aqueous media, and slurry with mild abrasion. Temperature: Typically ‑10 °C to +80 °C (short excursions to 90 °C). Corrosion: Resists fresh water, wastewater, seawater, sewage, weak acids/bases (pH 4–10), and oi...
    Read more

  • Why Electromagnetic Flowmeters Cannot Be Installed at the Highest Point or Downward Slope of the ...

    Electromagnetic flowmeters (EMF) work based on Faraday’s Law of Electromagnetic Induction, which requires that the measured conductive liquid must fully fill the pipeline and flow stably through the sensor’s magnetic field. Only in this way can the electrodes accurately detect the ind...
    Read more

  • Guided Wave Radar Level Transmitter

    Adopts time-domain reflectometry (TDR) principle, stable and reliable measurement. Not affected by temperature, pressure, steam, foam, vapor and dust. No influence by medium density, conductivity and viscosity changes. Suitable for corrosive, sticky, granular and powdery media. Small beam angle,...
    Read more
<< < Previous 20212223242526 Next > >> Page 23 / 129

Send your message to us: